Navman tracker plotter TRACKER 5600 Manuel d'utilisateur télécharger pdf (Page 31)

TRACKER 5600 Installation and Operation Manual

NAVMAN

Simulate mode is a way of becoming familiar with

the TRACKER (see section 2-6).

Warning: Never have simulate mode on when

the TRACKER is navigating on the water.

Simulate

Turn simulate mode

Off

Press MENU and select

simulate.

Select

Off.

Mode

There are two choices for

Mode

Normal

Simulates the boat moving from the selected

start point (see step 1 above) at the given

speed and heading. The options are:

Speed

: The simulated boat speed to use.

Heading

: The simulated bearing for the

boat to follow.

Tip: To calculate a heading, use the cursor

(see section 3-1-1).

Tip: As the boat moves, vary Heading to

simulate the boat moving off course.

13-11 Simulate setup

Demo

Simulates the boat moving along a route at a

given speed. When it reaches one end it

retraces the route in the other direction. Before

setting this mode enter at least one route (see

section 10-2-1). The options are:

Speed

: The simulated boat speed to use.

Route

: The route to follow.

To turn simulate mode on from this menu:

1 If turning Normal mode on, go to the chart

display. To start the simulation from the boat

position, press ESC to switch to centre on boat

mode. To start the simulation from a different

point, move the cursor to that point on the

chart.

2 In the Simulate setup menu, select

Simulate

and turn it on.

3 Select

Mode

and set it to

Normal

Demo

4 Select and enter the other data required for

simulate:

Normal requires

Speed

and

Heading

Demo requires

Speed

and

Route

14 Systems of several instruments

Several NAVMAN instruments can be connected

together to share data. There are two ways of

connecting instruments together, NavBus or NMEA.

NavBus

NavBus is a NAVMAN proprietary system that allows

systems of multiple instruments to be built using a

single set of transducers. When instruments are

connected by NavBus:

If the units, alarms or calibration are changed

in one instrument, then the values will

automatically change in all other instruments

of the same type.

Each instrument can be assigned to a group of

instruments (see section 13-8). If the backlight

is changed in an instrument in group 1, 2, 3 or

4 then the backlight will automatically change

in the other instruments in the same group.

If the backlight is changed in an instrument in

group 0 then no other instruments are affected.

If an alarm sounds, mute it by clearing the

alarm on any instrument which can display that

alarm.

NavBus and the TRACKER

The TRACKER can display data (e.g. depth,

speed, log and wind) from NAVMAN’s 3100

series instruments when connected.

NMEA

NMEA is an industry standard, but is not as flexible

as NavBus as it requires dedicated connections

between instruments. The TRACKER can:

Receive and display depth data.

Receive data from a GPS antenna.

Send GPS position and other navigation data

to an autopilot or other instrument.

Local offset

The difference between local time and UTC (GMT).

Change local offset when daylight saving time starts

and ends. The range is 0 to ± 13 hours, in 30 minute

steps.

13-10 Time setup

Time format

The options are 24 hour or 12 hour.

Date format

The options are dd/MMM/yy, MMM/dd/yy,

dd/MM/yy or MM/dd/yy.

1 2 ... 26 27 28 29 30 31 32 33 34 35 36 ... 41 42

Commentaires sur ces manuels

Pas de commentaire

Navman tracker plotter TRACKER 5600 Manuel d'utilisateur Page 31

Commentaires sur ces manuels

Produits connexes et manuels pour Navigateurs Navman tracker plotter TRACKER 5600